LED Signage Lighting Glossary

Twenty terms that decide whether an LED sign is specified correctly. Each entry gives the definition first, then the practical consequence that the definition implies for a sign face, an outdoor run or a power supply.

Why a glossary

Most signage sourcing disputes trace back to a term being used with two meanings — an IP rating assumed to cover the whole installation, a colour temperature mixed across one face, or a wattage quoted without headroom. These definitions are written to remove that ambiguity: each one states what the term means and what it does not mean.

Jump to: 1 · B · C · I · L · S · W

1

12V / 24V Low Voltage

The two nominal low-voltage DC systems around which LED modules, strips and their power supplies are standardised in signage.

The choice is mostly about current: at the same wattage, a 24V run draws half the current of 12V, halving voltage drop and allowing thinner cable over longer distances. Industry-standard practice limits voltage drop to about 3%; on 12V that often restricts a single feed to a few metres, while 24V roughly doubles the usable run before a second feed is needed.

Read the full article

B

Beam Angle

The angular width of the light cone from a source, measured in degrees between the directions where intensity falls to half of its peak.

A wide 170° beam — the rating on GMH modules — spreads light across a large face with fewer modules and fewer dark gaps, which suits deep channel letters and light boxes. Narrow beams under 60° concentrate output and create hot spots, so they are used for accents and grazing light rather than even face illumination. Module count falls roughly with the square of the area a beam must cover.

Read the full article

C

Channel Letter

A three-dimensional fabricated sign letter built from a face, return walls and a back, designed to be lit from inside so the letterform itself glows.

The depth of the return — typically 4–25 cm on illuminated letters, the range GMH modules are sized for — decides how far internal LEDs must throw light before the face. Returns under about 5 cm are the usual cause of scalloped, uneven faces, so module spacing and beam angle have to be selected together rather than independently.

Read the full article

COB LED

A chip-on-board LED in which many bare dies are mounted on a single substrate and covered by one continuous phosphor layer, creating one large emitting area instead of separate points.

Because the light comes from a continuous surface, COB removes the dotted look of multiple SMD emitters, which matters on signs viewed from close range. Industry-standard COB arrays run hotter and need a real heatsink; typical efficacy is 80–120 lm/W, so thermal design, not the die itself, usually sets the output you can actually achieve in an enclosed letter.

Read the full article

Color Temperature (Kelvin)

The colour appearance of a light source, stated in kelvin (K) by comparison with the colour of an ideal heated black body at that temperature.

Around 2700–3000 K reads warm and yellowish, 4000–4500 K is neutral, and 5000–6500 K is a cool blue-white. On signs, 6500 K looks crisp from a distance but can appear harsh up close, while warm white is often chosen for hospitality branding. Mixing two colour temperatures in one run is one of the most visible and most avoidable installation defects.

Read the full article

CRI (Colour Rendering Index)

A 0–100 scale describing how faithfully a light source reproduces the colours of objects compared with a reference source of the same colour temperature.

CRI 80 is the industry-standard minimum for general lighting; CRI 90+ is specified where brand colours and skin tones must look right, such as retail and hospitality signage. Higher CRI is not free — it typically costs 10–20% in efficacy — so colour fidelity and efficiency are separate decisions in a module specification.

Read the full article

CE / FCC / RoHS

Three distinct compliance marks: CE declares conformity with European health, safety and environmental rules, FCC governs electromagnetic emissions in the United States, and RoHS restricts hazardous substances in electronics.

These are legal market-access declarations, not quality certificates. CE and FCC address electromagnetic compatibility; RoHS limits substances such as lead and mercury to 0.1% by weight and cadmium to 0.01%. A credible supplier provides a Declaration of Conformity and test reports on request — a logo printed on a label is not evidence of compliance.

I

Injection Molded Module

An LED module whose lens and housing are formed by injecting molten plastic into a mold, producing one sealed, uniform light-emitting body.

Molding gives a consistent beam and a water-resistant shell at volume: tooling cost is amortised over thousands of units, so the per-module price falls sharply beyond roughly 1,000 pieces. The constraint is that lens geometry is fixed in the tool — a 170° lens cannot be widened without cutting a new mold, so the optical choice has to be right before production starts.

Read the full article

IP Rating (IP65 / IP67 / IP68)

An IEC 60529 ingress-protection code in which the first digit rates protection against solid particles and the second against water, with higher digits meaning greater protection.

The digits are not a simple quality ranking. IP65 resists a directed water jet, IP67 covers temporary immersion to 1 m for 30 minutes, and IP68 means continuous submersion beyond that. A sign is only as weatherproof as its weakest component: an IP67 module paired with an IP65 supply still fails at the supply, so specify the whole chain.

Read the full article

IP67

An ingress-protection rating certifying complete protection against dust and the ability to withstand temporary immersion in water up to 1 metre for 30 minutes.

IP67 is the practical benchmark for outdoor sign modules because it tolerates driving rain and short-term flooding without water reaching the optics. It is not a submersion rating — that is IP68 — and the seal is weakest at cable entries and connectors, so outdoor runs need IP67-rated joins as well as IP67-rated modules. GMH rates its sign modules at IP67.

Read the full article

L

LED (Light-Emitting Diode)

A semiconductor device that emits light when current passes across its p–n junction, converting electrical energy directly into light instead of heating a filament.

A typical white LED turns roughly 30–50% of its input into visible light, while an incandescent lamp converts only about 5%, which is why LED signage runs cool enough to sit inside a sealed acrylic letter. The trade-off is heat at the junction: industry-standard practice keeps the junction below 85°C, because every 10°C rise above that roughly halves the rated life.

LED Module

A small circuit board carrying one or more LEDs plus current-limiting components, bonded inside a channel letter or light box to act as the light source.

One sign may use dozens to hundreds of modules. At an industry-standard 0.5–1 W each, a 100-module run draws 50–100 W, so the supply needs at least 20–30% headroom. Modules rated for 4–25 cm side heights cover both shallow light boxes and deep channel letters, which is why that single specification is a useful first filter when shortlisting.

Read the full article

Lumen

The SI unit of luminous flux, expressing the total visible light a source emits in all directions, weighted to the sensitivity of the human eye.

Lumens measure total output, not how bright a surface looks — that is lux. A module rated at 100 lm spreads that light over whatever area its beam covers, so doubling the covered area roughly halves the illuminance. This is why a lumen figure alone cannot predict how a finished sign will read at night; beam angle and mounting distance matter just as much.

Read the full article

Luminous Efficacy (lm/W)

The ratio of luminous flux emitted to electrical power consumed, expressed in lumens per watt, describing how efficiently a source converts electricity into visible light.

Industry-standard white LED modules today deliver roughly 80–130 lm/W, so a 1 W module produces about 80–130 lm. Efficacy falls as colour temperature drops, as CRI rises, and as junction temperature climbs — which is why datasheet figures are measured at 25°C and the output of a hot, installed, enclosed sign is noticeably lower.

Read the full article

LED Matrix Panel / Pixel Pitch

A grid of individually addressable LED pixels used for graphics and video, with pixel pitch defined as the centre-to-centre distance between neighbouring pixels in millimetres.

Smaller pitch means higher resolution and a closer minimum viewing distance: P2.6 to P4 is typical for near-field signage, while coarser pitches suit long-distance viewing. Panels are tiled to reach a target resolution; GMH lists matrix configurations such as 32×320, 32×256, 32×160 and 16×96. Physical panel size equals pitch times pixel count, so the same pixel height is a different physical size at different pitches.

S

SMD LED

A surface-mount light-emitting diode soldered directly onto the face of a circuit board rather than inserted through a hole, identified by package codes such as 2835, 3528 or 5050.

The digits are the footprint in tenths of a millimetre: a 2835 die measures 2.8 × 3.5 mm. Smaller packages allow tighter spacing and smoother faces, but one 2835 emitter typically produces only 20–30 lm, so sign modules connect several in series to reach useful output. A 5050 package delivers roughly two to three times that per die.

Read the full article

Switching Power Supply (SMPS)

A power converter that turns mains AC into a regulated low-voltage DC output by switching at high frequency rather than burning off excess voltage as heat.

An SMPS typically runs at 85–93% efficiency, far above a linear supply, which is why a 100 W LED load is normally paired with a 150 W unit for headroom. Signage lines commonly include 100 W, 150 W, 200 W and 350 W models, GMH range included. Undersizing shortens life; oversizing beyond roughly twice the load adds cost with little benefit.

Read the full article

Silicone Neon Flex

A linear luminaire in which LEDs are sealed inside a flexible silicone extrusion that diffuses their output into a continuous, neon-like line of light.

Silicone neon flex bends to tight curves — industry-standard side-bend versions handle roughly a 20–30 mm bend radius — and its sealed body commonly carries an IP67 rating for outdoor use. It can only be cut at marked points, typically every 25–50 mm, and pushing one run past its specified maximum length without a mid-feed produces a visible drop in brightness toward the far end.

Read the full article

Series vs Parallel Wiring

Two ways of connecting multiple LEDs: in series the same current passes through each device in a single path, while in parallel each device sits on its own branch across the supply.

In a series string, one open-circuit module kills the whole run; in parallel, a single failure only dims one branch. Parallel wiring multiplies current, though, so cable must be sized for total amps — industry-standard 18 AWG carries roughly 10 A and 16 AWG about 13 A in short chases. That is why long sign runs usually split into several parallel, individually fused branches rather than one large circuit.

Read the full article

W

Warranty

A manufacturer written commitment to repair or replace a product that fails within a stated period under normal use.

Warranty length often reveals where a maker expects failures: in LED signage, modules are commonly covered for 3 years, strips for 2 years and power supplies for 2 years — the split GMH applies. What matters more than the headline number is the exclusion list; most warranties cover product defects but not water ingress from poor installation, and many require proof of correct voltage and in-spec operating temperature.

Read the full article

IP ratings follow the IEC 60529 ingress-protection scheme. Other terms follow common LED and signage industry usage; where usage differs from a formal standard, the practical meaning is noted in the detail paragraph.

Tell us your sign project, get a product recommendation

Share your sign design — letter depth, face material, indoor or outdoor — and we will recommend the right LED modules, strip, power supply and protection rating, with a quotation. No obligation.