12V Switching Power Supplies for LED Signage

IP67 waterproof 36W–350W and 12 mm ultra-slim IP20 45W–350W LED switching power supplies. Dual 12V/24V output, AC170–265V input, 3-year warranty on IP67.

IP67 waterproof 12V LED switching power supply with sealed glanded case and hanging bracket
IP67 -F waterproof series — sealed glands, hanging bracket. More PSU photos below.
Short answer

An LED switching power supply converts mains AC voltage into the low-voltage DC that LED signs and strips require, with 12V and 24V outputs common in signage. GMH builds two families: the MH-12Vxx-F waterproof series (36W–350W, IP67, −30°C to +45°C, 3-year warranty) and the MH-12Vxx-B ultra-slim series (45W–350W, 12 mm case, IP20, 0°C to +45°C, 2-year warranty). Both take AC170–265V 50/60Hz input and deliver dual 12V/24V DC.

Scope: what this product page covers

This page covers two switching power supply families for LED signage: the MH-12Vxx-F waterproof series (MH-12V36-F, 45-F, 60-F, 100-F, 150-F, 200-F, 250-F, 300-F, 350-F; 36W–350W; IP67; AC170–265V 50/60Hz; −30°C to +45°C; 3-year warranty) and the MH-12Vxx-B ultra-slim series (MH-12V45-B, 60-B, 100-B, 150-B, 200-B, 250-B, 300-B, 350-B; 45W–350W; IP20; 12 mm case up to 250W, 28 mm at 300W and 350W; 0°C to +45°C; 2-year warranty). It does not cover high-voltage industrial rectifiers, battery chargers, solar inverters or dimmable constant-current drivers.

Specifications

Waterproof series (-F)36W / 45W / 60W / 100W / 150W / 200W / 250W / 300W / 350W
Ultra-slim series (-B)45W / 60W / 100W / 150W / 200W / 250W / 300W / 350W
Input voltageAC170–265V, 50/60Hz (both series)
OutputDual 12V and 24V DC (e.g. 12V5A / 24V2.5A on the 60W unit)
Protection ratingIP67 on the -F series; IP20 on the -B series
Operating temperature−30°C to +45°C (-F); 0°C to +45°C (-B)
Housing170×45×23 mm to 310×95×32 mm (-F); 12 mm case to 250W, 28 mm at 300–350W (-B)
Recommended load0.8 (80% derating recommended)
Minimum order200 pcs per model
Warranty3 years on IP67 -F series; 2 years on IP20 -B series

Materials

  • Aluminium and steel enclosure
  • Switching-mode power electronics
  • Sealed connectors and cable glands on IP67 models
  • Potting compound for waterproof versions

Manufacturing process

  1. Load calculation We add up the total wattage of the connected LEDs and apply roughly 20% headroom so the supply is not run at its limit. A sign drawing 80W, for example, is matched to a 100W unit rather than an 80W one.
  2. Environment selection Indoor, dry locations use a standard rainproof or indoor unit; exposed outdoor signs require an IP67 waterproof model. Cable entry and gland sealing are chosen at this stage.
  3. Assembly and testing Units are assembled with switching circuitry and protective features, then tested for output stability, load regulation and the overvoltage, overcurrent and short-circuit protections.
From the shop floor

LED Power Supplies in production

Typical applications

  • Powering LED channel letters and lightboxes
  • Driving LED strip and neon flex runs
  • Outdoor and rain-exposed signage
  • Advertising lightboxes and display cases
  • Architectural LED accent installations

Quality and documentation

  • ISO 9001 quality management system
  • Dual 12V/24V output on every model, 0.8 recommended load factor
  • IP67 sealed enclosure on the -F series, −30°C to +45°C rated
  • Overvoltage, overcurrent and short-circuit protection
  • 3-year warranty on IP67 -F series; 2-year warranty on IP20 -B series

What we do not do

We do not supply mains distribution boards or dimmable constant-current drivers, and these supplies must be installed by a qualified electrician in line with local electrical codes. Do not run a supply above its 0.8 recommended load factor. The IP20 -B series is for dry indoor cabinets only — it must not be used in a rain-exposed location. Sizing guidance assumes a 12V LED load; 24V loads need recalculation.

LED Power Supplies

Technical questions

How do I choose the right power supply wattage?

Add the wattage of every LED on the run and work to the 0.8 recommended load factor, which is roughly 25% headroom. A sign drawing around 120W should use the 150W unit; for 300W total, use the 350W unit or split the load across two supplies. Running a supply close to its limit shortens its life.

What is the difference between the -F and -B power supply series?

The -F series is IP67 sealed for exposed outdoor signage and covers 36W–350W with a 3-year warranty and a −30°C to +45°C range. The -B series is IP20 and only 12 mm thick up to 250W, made for tight indoor lightboxes and cabinets, rated 45W–350W with a 2-year warranty and 0°C to +45°C.

Can one power supply drive several channel letters?

Yes, as long as the combined wattage stays inside the 0.8 load factor. Remember that long cable runs cause voltage drop, so group letters near the supply or use thicker cable for distant runs.

What warranty do the power supplies carry?

The IP67 -F waterproof series carries a 3-year warranty and the IP20 -B ultra-slim series carries a 2-year warranty, both covering manufacturing defects in normal use. Damage from overloading, incorrect mains voltage or improper installation is excluded.

Related

Adjacent products and capabilities

LED Modules

LED modules are small, self-contained circuit boards or injection-moulded units that carry one or more LEDs and are mounted in rows inside channel letters and lightboxes to illuminate sign faces evenly. GMH makes the MH-series of 12V injection-moulded LED modules from 0.4W to 4W with 165°–175° beam angles, rated for 50,000 hours with lumen depreciation below 6%, from MOQ 200 pcs per model and a 5-day lead time on orders up to 1,000 sets..

View product

LED Strips & Neon Flex

LED strip lights are flexible circuit boards populated with surface-mount LEDs, while silicone neon flex is a strip enclosed in an extruded silicone diffuser that produces a smooth, continuous line of light. GMH supplies S-shaped lens strips from 12.5 mm to 50 mm board width with 10 mm 170°, 13.5 mm 180° and 18 mm 15°×35° lenses at 7.2–20W/m, flowing and pixel strips on 12V, 24V and 5V with external 16703 or built-in 2815 ICs, and silicone neon flex from 8 mm to 8×16 mm in 15 colours, with 2-year warranties..

View product

LED Matrix Panels

LED matrix panels are configurable grids of addressable LEDs that display text, graphics and simple animations, widely used on vehicle signs, shop windows, food trucks and stage backdrops. GMH supplies flexible matrix panels in formats from 32×320 down to 16×96 pixels, suited to vehicle displays, advertisements, shop windows and event signage, exported to more than 100 countries..

View product

Quality & Assurance

ISO 9001 quality system, powered ageing and IP65/IP67 waterproof checks on sealed products.

Quality capability

Tell us your sign project, get a product recommendation

Share your sign design — letter depth, face material, indoor or outdoor — and we will recommend the right LED modules, strip, power supply and protection rating, with a quotation. No obligation.