Technical

How to Size a Power Supply for LED Signage

Add up LED wattage, apply 20% headroom and choose a 12V or 24V supply from 36W to 350W. A practical sizing guide with worked examples.

GMH Lighting · Published September 1, 2026 · Updated October 10, 2026 · 5 min read

Short answer

Sizing a power supply for LED signage means adding the wattage of every connected LED, applying a 20% headroom margin, and choosing a 12V or 24V unit rated at or above the result. Common ratings are 36W to 350W. For example, a 120W load needs at least a 150W supply. Undersizing causes flicker; oversizing wastes little because LEDs draw only what they need.

Key points

  • Total LED wattage × 1.2 gives the minimum supply rating; a 120W load needs 150W.
  • Match voltage exactly: 12V loads need 12V supplies, 24V loads need 24V supplies.
  • Common ratings are 36W to 350W; pick the next one above the load.
  • A supply running at about 80% of its rating stays cooler and lasts longer.

The core calculation

Sizing a power supply is arithmetic, not guesswork. Three steps cover almost every LED sign:

  1. Add the wattage of every LED module or strip in the circuit.
  2. Multiply the total by 1.2 to build in 20% headroom.
  3. Choose the next available rating at or above that number, in the correct voltage.

The formula is simply:

Minimum supply rating = total LED wattage × 1.2

For example, a sign with 100W of LED load needs a supply of at least 120W. The next standard rating up would be 150W.

Worked examples

Total LED loadWith 20% headroomRecommended supply
60W72W100W
100W120W150W
120W144W150W
160W192W200W
300W360W350W or split into two supplies

Note the last row: when the load exceeds a single supply, split the sign across two units rather than pushing one to its limit. Two 200W supplies are often safer and easier to wire than one oversized unit.

Standard ratings explained

Sign installations commonly use 36W to 350W power supplies. These are convenient steps that keep most projects within one or two units.

RatingTypical use
100WSmall letters, lightboxes, prototypes
150WMedium storefront signs
200WLarge channel letters, long strip runs
350WFull-store signage, multiple signs on one supply

Selecting the next size up gives you headroom without paying for capacity you will never use. Explore the available LED power supplies to match voltage and rating.

Why voltage must match

Voltage is not a suggestion. A 12V LED connected to a 24V supply will be overdriven and fail quickly; a 24V LED on 12V will be dim or will not light. Check the label on both the LED and the supply before ordering.

Voltage also affects current, and current affects cable loss. At 12V, the same power draws twice the current of a 24V system, so long cable runs lose more voltage and heat up. For large signs, 24V is often the easier choice because it reduces current and allows thinner cable.

Headroom and heat

The 20% margin is not wasted capacity. LEDs are constant-load devices: a 100W LED load connected to a 150W supply still draws about 100W. The extra rating simply means the supply runs cooler and handles inrush current when the sign switches on.

Heat is the main enemy of power supplies. A unit loaded to about 80% of its rating, mounted where air can circulate, will last significantly longer than one running at its maximum in a sealed box. Leave ventilation space and avoid stacking supplies tightly.

Common mistakes

  • Adding wattage without checking voltage first. Voltage mismatch destroys LEDs instantly.
  • Using the supply’s maximum rating as the target. Always leave 20% headroom.
  • Ignoring cable runs. Long 12V runs need thicker cable to avoid voltage drop.
  • Sealing a supply in a hot enclosure without ventilation. Heat shortens life.
  • Forgetting future additions. Headroom gives you room to extend the sign later.
  • Ignoring inrush current. LED supplies can draw a brief surge at switch-on, which the headroom absorbs.
  • Buying on price alone. A cheap supply that fails takes the whole sign offline and costs more in callouts than a quality unit.

After installation, confirm the output voltage at the supply terminals with a multimeter under full load. A reading below the rated voltage points to cable loss or an undersized unit, and it is far easier to correct at commissioning than after the sign has been mounted.

Worked example: a two-sign storefront

Imagine a shop with two signs. The front channel letter uses 12V modules totalling 70W, and the window lightbox uses 24V LED strips totalling 90W.

  1. Keep the circuits separate. Because the voltages differ, size one supply for each circuit. Do not combine a 12V and a 24V load on one output.
  2. Front sign. 70W × 1.2 = 84W. The next available rating is 100W at 12V.
  3. Window sign. 90W × 1.2 = 108W. The next available rating is 150W at 24V.
  4. Check the load. Each supply runs at roughly 70–72% of its rating, which leaves useful headroom and keeps temperatures moderate.

If the window sign is later extended with another 30W of strip, the 150W supply still covers it: 120W × 1.2 = 144W, just within the rating. This is why headroom is worth paying for at the design stage.

For larger projects, a useful rule is to keep each supply below about 80% of its rating and to split loads across multiple units rather than relying on a single 350W supply. Two smaller units also mean that a single failure blinds only part of the installation.

Scope and limits

This page does not cover mains wiring, breaker sizing or electrical code compliance, which must be handled by a qualified electrician under local regulations. It does not address dimming controllers, constant-current drivers or battery-backed systems, all of which have different sizing rules. It also excludes three-phase and high-voltage industrial installations.

This article describes general manufacturing practice for machined and fabricated components. It is not a substitute for a drawing-specific engineering review — tolerances, material selection and process capability depend on the individual part.

Questions

Frequently asked

How much headroom should a LED power supply have?

A 20% headroom is the standard rule: if your LEDs draw 100W, use a supply rated for at least 120W. This covers inrush current and allows for future additions. Running a supply near 80% of its rating also reduces heat and extends life.

Can I use a 24V supply for 12V LED strips?

No. A 12V strip on 24V will draw roughly double the current and burn out. If you must mix voltages, use a proper 24-to-12V converter. Keep the whole sign on one voltage to keep sizing simple and safe.

What happens if my power supply is too small?

An undersized supply will flicker, dim under load or shut down on overload, and may fail early. Calculate total wattage, add 20%, and choose the next rating up — for 160W, choose 200W. Always confirm the output voltage matches the LEDs.

Is a bigger power supply always better?

Up to a point. A 350W supply for a 50W load works but costs more and takes more space. The practical choice is the next rating above the calculated load with 20% headroom, rather than the largest unit available.

Tell us your sign project, get a product recommendation

Share your sign design — letter depth, face material, indoor or outdoor — and we will recommend the right LED modules, strip, power supply and protection rating, with a quotation. No obligation.